故障代码 |
错误含义 |
具体描述 |
FIP/Corrective Action |
- |
Y Toner Life Warning 黄色碳粉寿命警告 |
The yellow toner cartridge has reached the set toner supply time limit but it can still work. 黄色碳粉盒已达到规定时限碳粉供应,但它仍然可以工作。 |
FIP-1 75 |
- |
M Toner Life Warning 红色碳粉寿命警告 |
The magenta toner cartridge has reached the set toner supply time limit but it can still work. 红色碳粉盒已达到规定时限碳粉供应,但它仍然可以工作。 |
FIP-1 76 |
- |
C Toner Life Warning 青色碳粉寿命警告 |
The cyan toner cartridge has reached the set toner supply time limit but it can still work. 青色碳粉盒的已达到规定时限碳粉供应,但它仍然可以工作 |
FIP-1 77 |
- |
K Toner Life Warning 黑色碳粉寿命警告 |
The black toner cartridge has reached the set toner supply time limit but it can still work. 黑色碳粉盒的已达到规定时限碳粉供应,但它仍然可以工作 |
FIP-1 78 |
- |
Toner Bottle Life Warning 碳粉满警告 |
The waste toner bottle is detected FULL by the SENSOR TNER FULL but can still work 废碳粉检测传感器到检测废碳粉瓶满,但仍然可以工作。 |
FIP-1 79 |
- |
Xero CRU Life Warning 感光鼓(CRU)寿命警告 |
The drum has exceeded its specified rotation count but it can still work. 鼓已超过其指定的旋转数,但它仍然可以工作。 |
FIP-1 80 |
%s Check paper %本票纸 |
IOT Paper Size Mismatch 互操作性测试纸张尺寸不匹配 |
Paper Size Mismatch detected. 纸张尺寸不匹配检测。 (打开/关闭托盘或删除旁路纸盘并重新加载文件) |
Open/close the tray or remove and reload paper in Bypass Tray. |
(No LCD Display) 无液晶显示器 |
Static Jam (Remain at OHP) 静态果酱(留在铂) |
The SENSOR OHP was turned ON at Power ON or when the I/L was closed. (Static Jam) 该传感器铂被打开或上电时的I / L的关闭。(静态果酱) |
FIP-1 39 |
001-358 |
IOT Fan Error Fuser 互操作性测试范错误定影 |
Fan Error Fuser detected.范错误定影检测。 |
Power OFF/ON |
001-360 |
IOT Fan Error Rear 范错误后互联互通 |
Fan Error Rear detected.范后发现错误。 |
Power OFF/ON |
003-356 |
NVRAM ErrorNVRAM中错误 |
An error occurred in the NVRAM on the PWBA MCU. 错误发生在微控制器上的PWBA NVRAM中。 |
FIP-1 43 |
004-310 |
Communication Error Feeder 直属通信错误 |
A communication error occurred between the PWBA MCU and the feeder. 阿之间发生的通讯错误的PWBA MCU和接驳。 |
FIP-1 40 |
004-311 |
Communication Error Duplex 通讯错误双工 |
A communication error occurred between the PWBA MCU and the Duplex. 阿之间发生的通讯错误的PWBA MCU和双工。 |
FIP-1 41 |
004-321 |
TR0 Failure TR0传感器故障 |
The PWBA MCU did not receive the output signals from the SENSOR TR-0 (TR0 Sensor) at the specified timing. PWBA MCU没有在指定定时方面收到从传感器TR-0((TR0传感器)输出信号.。 |
FIP-1 44 |
004-324 |
Humidity Sensor Error 湿度传感器错误 |
The inputs from the SENSOR HUM & TEMP are out of the specifications. 从本田和温度传感器的输入,是从规格 |
FIP-1 58 |
004-332 |
Deve Home Position Sensor Error 德韦首页位置传感器错误 |
The PWBA MCU did not receive the output signals from the Rotary Home Position Sensor within the specified time after the Rotary Developer had started rotation. 在指定作为时间以内PWBA MCU 不确实收到从旋转的国内位置传感器从输出到信号,在旋转的开发者已经以开始转动之后。 |
FIP-1 46 |
本文由广州恒镭办公设备有限公司 打印机粉盒http://www.hoa168.com整理发布。
相关标签:施乐525A故障代码表,施乐525A故障代码,施乐525A维修代码,